ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Bearing Housing Design Guide

When a bearing goes into a 3D-printed part, a hole that is too tight cracks the part or damages the bearing, and one that is too loose lets it wobble. Model the bearing hole, shoulders and walls to this guide so the bearing presses in once and spins smoothly.

01 · SIZE CHART

Size chart

Swipe the table sideways →

ModelZZ shielded / openBore × OD × Widthd × D × BPress-fit holeØH tightSlip-fit holeremovableHole depthflushHousing shoulderØDa min.Shaft shoulderØda max.Min. wallt
MR117ZZMR1177 × 11 × 3open 2.511.111.253open 2.510.27.83
MR137ZZMR1377 × 13 × 4open 313.113.254open 311.88.23
687ZZ6877 × 14 × 5open 3.514.114.255open 3.512.68.43
697ZZ6977 × 17 × 517.117.2551593
607ZZ6077 × 19 × 619.119.25616.69.43
627ZZ6277 × 22 × 722.122.25719103
637ZZ6377 × 26 × 926.126.25922.210.83
MR128ZZMR1288 × 12 × 3.5open 2.512.112.253.5open 2.511.28.83
MR148ZZMR1488 × 14 × 4open 3.514.114.254open 3.512.89.23
688ZZ6888 × 16 × 5open 416.116.255open 414.49.63
698ZZ6988 × 19 × 619.119.25616.810.23
608ZZ6088 × 22 × 722.122.25719.210.83
628ZZ6288 × 24 × 824.124.25820.811.23
638ZZ6388 × 28 × 928.128.25924123
689ZZ6899 × 17 × 5open 417.117.255open 415.410.63
699ZZ6999 × 20 × 620.120.25617.811.23
609ZZ6099 × 24 × 724.124.25721123
629ZZ6299 × 26 × 826.126.25822.612.43
639ZZ6399 × 30 × 1030.130.251025.813.23
6700ZZ670010 × 15 × 4open 315.115.254open 314113
6800ZZ680010 × 19 × 519.119.25517.211.83
6900ZZ690010 × 22 × 622.122.25619.612.43
6000ZZ600010 × 26 × 826.126.25822.813.23
6200ZZ620010 × 30 × 930.130.25926143
6300ZZ630010 × 35 × 1135.135.251130153.5
6701ZZ670112 × 18 × 418.118.25416.813.23
6801ZZ680112 × 21 × 521.121.25519.213.83
6901ZZ690112 × 24 × 624.124.25621.614.43
6001ZZ600112 × 28 × 828.128.25824.815.23
16001ZZ1600112 × 28 × 728.128.25724.815.23
6201ZZ620112 × 32 × 1032.132.251028163.2
6301ZZ630112 × 37 × 1237.137.251232173.7
6802ZZ680215 × 24 × 524.124.25522.216.83
6902ZZ690215 × 28 × 728.128.25725.417.63
6002ZZ600215 × 32 × 932.132.25928.618.43.2
16002ZZ1600215 × 32 × 832.132.25828.618.43.2
6202ZZ620215 × 35 × 1135.135.251131193.5
6302ZZ630215 × 42 × 1342.142.251336.620.44.2
6803ZZ680317 × 26 × 526.126.25524.218.83
6903ZZ690317 × 30 × 730.130.25727.419.63
6003ZZ600317 × 35 × 1035.135.251031.420.63.5
16003ZZ1600317 × 35 × 835.135.25831.420.63.5
6203ZZ620317 × 40 × 1240.140.251235.421.64
6303ZZ630317 × 47 × 1447.147.251441234.7
6804ZZ680420 × 32 × 732.132.25729.622.43.2
6904ZZ690420 × 37 × 937.137.25933.623.43.7
16004ZZ1600420 × 42 × 842.142.25837.624.44.2
6004ZZ600420 × 42 × 1242.142.251237.624.44.2
6204ZZ620420 × 47 × 1447.147.251441.625.44.7
6304ZZ630420 × 52 × 1552.152.251545.626.45.2
6805ZZ680525 × 37 × 737.137.25734.627.43.7
6905ZZ690525 × 42 × 942.142.25938.628.44.2
16005ZZ1600525 × 47 × 847.147.25842.629.44.7
6005ZZ600525 × 47 × 1247.147.251242.629.44.7
6205ZZ620525 × 52 × 1552.152.251546.630.45.2
6305ZZ630525 × 62 × 1762.162.251754.632.46.2
6806ZZ680630 × 42 × 742.142.25739.632.44.2
6906ZZ690630 × 47 × 947.147.25943.633.44.7
16006ZZ1600630 × 55 × 955.155.25950355.5
6006ZZ600630 × 55 × 1355.155.251350355.5
6206ZZ620630 × 62 × 1662.162.251655.636.46.2
6306ZZ630630 × 72 × 1972.172.251963.638.47.2
6807ZZ680735 × 47 × 747.147.25744.637.44.7
6907ZZ690735 × 55 × 1055.155.251051395.5
16007ZZ1600735 × 62 × 962.162.25956.640.46.2
6007ZZ600735 × 62 × 1462.162.251456.640.46.2
6207ZZ620735 × 72 × 1772.172.251764.642.47.2
6307ZZ630735 × 80 × 2180.180.252171448
6808ZZ680840 × 52 × 752.152.25749.642.45.2
6908ZZ690840 × 62 × 1262.162.251257.644.46.2
16008ZZ1600840 × 68 × 968.168.25962.445.66.8
6008ZZ600840 × 68 × 1568.168.251562.445.66.8
6208ZZ620840 × 80 × 1880.180.251872488
6308ZZ630840 × 90 × 2390.190.252380509
6809ZZ680945 × 58 × 758.158.25755.447.65.8
6909ZZ690945 × 68 × 1268.168.251263.449.66.8
16009ZZ1600945 × 75 × 1075.175.251069517.5
6009ZZ600945 × 75 × 1675.175.251669517.5
6209ZZ620945 × 85 × 1985.185.251977538.5
6309ZZ630945 × 100 × 25100.1100.2525895610
6810ZZ681050 × 65 × 765.165.25762536.5
6910ZZ691050 × 72 × 1272.172.251267.654.47.2
16010ZZ1601050 × 80 × 1080.180.251074568
6010ZZ601050 × 80 × 1680.180.251674568
6210ZZ621050 × 90 × 2090.190.252082589
6310ZZ631050 × 110 × 27110.1110.2527986211
6811ZZ681155 × 72 × 972.172.25968.658.47.2
6911ZZ691155 × 80 × 1380.180.251375608
16011ZZ1601155 × 90 × 1190.190.251183629
6011ZZ601155 × 90 × 1890.190.251883629
6211ZZ621155 × 100 × 21100.1100.2521916410
6311ZZ631155 × 120 × 29120.1120.25291076812
6812ZZ681260 × 78 × 1078.178.251074.463.67.8
6912ZZ691260 × 85 × 1385.185.251380658.5
16012ZZ1601260 × 95 × 1195.195.251188679.5
6012ZZ601260 × 95 × 1895.195.251888679.5
6212ZZ621260 × 110 × 22110.1110.25221007011
6312ZZ631260 × 130 × 31130.1130.25311167413
6813ZZ681365 × 85 × 1085.185.251081698.5
6913ZZ691365 × 90 × 1390.190.251385709
16013ZZ1601365 × 100 × 11100.1100.2511937210
6013ZZ601365 × 100 × 18100.1100.2518937210
6213ZZ621365 × 120 × 23120.1120.25231097612
6313ZZ631365 × 140 × 33140.1140.25331258014
6814ZZ681470 × 90 × 1090.190.251086749
6914ZZ691470 × 100 × 16100.1100.2516947610
16014ZZ1601470 × 110 × 20110.1110.25201027811
6014ZZ601470 × 110 × 20110.1110.25201027811
6214ZZ621470 × 125 × 24125.1125.25241148112.5
6314ZZ631470 × 150 × 35150.1150.25351348615

Unit: mm. Press-fit hole = OD + 0.1, slip-fit hole = OD + 0.25 (FDM-printed holes usually come out 0.1–0.2 smaller; print a test ring first). Hole depth = bearing width (add or subtract if the bearing should stick out or sit deeper). Housing shoulder = OD − 0.2 × (OD − bore) and shaft shoulder = bore + 0.2 × (OD − bore), so they touch only the outer or inner ring and never the shield or cage. Minimum wall = 10% of the OD, at least 3 mm. Open bearings (no shields, model without ZZ, e.g. 608) have the same bore and OD as ZZ; the small text under each model is the open model number. Where the open version is narrower (MR117, MR137, MR128, MR148, 687–689 and 6700), its width and hole depth are marked “open”; model the hole for the bearing you actually use.

02 · CROSS SECTION

Housing cross section

ØHØDaØdatEntry chamfer 0.5Housing (printed part)BearingShaft
ØHBearing hole: use the press-fit size, or the slip-fit size if the bearing must come out again. Add a 0.5 mm chamfer at the opening so the bearing lines up easily.
ØDaHousing shoulder: leave a lip at the bottom of the hole for the bearing to sit on. Its inner diameter must not be smaller than the table value, or it rubs the shield (the cage on open bearings) and the bearing will not turn.
ØdaShaft shoulder: the step on the shaft must touch only the inner ring; keep it no larger than the table value.
tWall: keep at least the listed thickness around the bearing hole so the part does not crack when the bearing is pressed in.

03 · FIT

Choosing a fit

  1. Press fit (tight): The most common choice. The hole wall grips the bearing, so nothing else is needed; best where it is rarely removed. Press on the outer ring only, slowly, using a flat plate or another bearing as a pusher.
  2. Slip fit + retainer: A slightly loose hole; after the bearing goes in, hold it with a cover plate, circlip or screws. Easy to take apart and service.
  3. Glued: Use the slip-fit size and put a little CA glue or epoxy on the outer ring. Keep glue out of the bearing or it will seize.
  4. Embedded while printing: Pause the print at the top of the hole, drop the bearing in and continue, so it is fully enclosed (mention it in your quote and we will do it).

04 · DESIGN TIPS

Design tips

Reading the model number

  • MR, 6xx: miniature bearings, e.g. 608ZZ = 8 mm bore, 22 mm OD, 7 mm wide.
  • 67, 68, 69 series: thin section; small OD for tight spaces.
  • 60, 62, 63 series: for the same bore, a higher number means a larger, stronger bearing.
  • ZZ = metal shields on both sides (dust-resistant, not waterproof); without ZZ (e.g. 608) = open, no shields. We sell Taiwan-made and KOYO (Japan) bearings, shielded (ZZ) and open; KOYO is price on request.

Print orientation

  • Print the bearing hole perpendicular to the build plate (axis pointing up) for the roundest, most accurate hole.
  • If the hole touches the build plate, the first layer flares out (elephant's foot); add a 0.3–0.5 mm chamfer at the opening.
  • Horizontal holes sag at the top and press in tighter; add 0.1 mm to the hole or use a slip fit with a retainer.

Shafts and retention

  • Use a metal shaft (h6–k6 tolerance); printed shafts suit only low speed and light loads.
  • Hold the bearing on both sides: a shoulder on one side and a cover plate, circlip or screws on the other.
  • When two bearings carry one shaft, space them as far apart as possible, at least 2× the shaft diameter.

Speed and load

  • Printed parts slowly deform under constant load (creep); for long-term loads use PETG or better and thicker walls.
  • High speed creates heat and PLA softens at about 55 °C; near motors or fans use ABS, ASA or PC.
  • ZZ shields are not enough for water or fine dust; add a seal or ask us.

05 · MATERIALS

Materials

GoodPLA / PLA+Accurate and easy to print; fine for light loads and low speed, but deforms under long-term load or heat.
GoodPETGTough and less likely to crack when pressing in; the first choice for general mechanisms.
GoodABS / ASA / PCHeat-resistant and strong; for housings near motors, hot areas or higher loads.
GoodPA / carbon-fiber compositesBest stiffness and wear resistance for long-running mechanisms (confirm the material with us).
CautionResin (SLA)Brittle and cracks easily when pressing in; use a slip fit with a retainer, or ask us first.
CautionTPU (flexible)Too soft, the bearing wobbles; it works as a damping sleeve, but needs a separate rigid housing.

06 · CHECKLIST

Checklist before you submit

Questions about your design? Send it to us first

Attach your file or a screenshot and we will check the bearing model and hole sizes. Bearings can be ordered together with your 3D prints.

Contact us on LINE Download PDF