ShopInstant QuoteFAQDesign GuidesAboutQuote LookupOrder StatusCartMy Account中文Upload a Model · Instant Quote
← Back

DESIGN GUIDELINE

Screw & Nut Hole Design Guide

When 3D-printed parts are assembled with screws, the hole size decides whether the screw goes in and whether it strips. Model the clearance holes, counterbores and nut pockets to this guide so screw heads and nuts sit flush and the parts go together the first time.

01 · SIZE CHART

Size chart

Swipe the table →

ThreadpitchClearance holescrew passesTapped into plasticscrew bitesSocket head counterboredia. × depthFlat head countersink90°, top dia.Hex nut pocketacross flats × depthHex keysocket head
M1.60.351.81.43.6 × 1.9——1.5
M20.42.41.73.6 × 2.34.44.3 × 1.71.5
M2.50.452.92.14.4 × 2.85.45.3 × 2.12
M30.53.42.66.1 × 3.36.15.8 × 2.42.5
M3.50.63.93——6.3 × 3—
M40.74.53.47.6 × 4.38.47.3 × 33
M50.85.54.39.1 × 5.310.48.3 × 3.74
M616.65.110.6 × 6.312.410.3 × 5.25
M81.2596.813.6 × 8.316.413.3 × 6.76
M101.5118.616.6 × 10.320.417.3 × 8.28
M121.7513.510.318.6 × 12.324.419.3 × 10.210

Unit: mm. Clearance holes follow ISO 273 (medium). Tapped hole = thread diameter − pitch + 0.1. Counterbore = head diameter + 0.6, depth = head height + 0.3. Countersink = head diameter + 0.4 (90°). Nut pocket = across flats + 0.3, depth = nut thickness + 0.2. Head and nut sizes are those of the stainless screws and nuts we sell (same as in our shop); sizes we do not sell (grey) use standard values.
Model the holes with these values directly; no shrinkage compensation needed. For larger runs or tight fits, print a test hole first.

02 · CROSS SECTION

Cross section

ØChead + 0.3ØACounterborePart surfaceØC90°ØACountersinkØASnut + 0.2Clearance + nut pocketØTscrew + 1Tapped (blind hole)
ØAClearance hole: the screw passes through freely. When two parts are clamped together, the part under the screw head gets the clearance hole.
ØCCounterbore: lets a socket head sit flush; depth = head height + 0.3. Flat head screws need a 90° countersink, top diameter = head diameter + 0.4.
SNut pocket: hexagonal, across flats = nut + 0.3, depth = nut thickness + 0.2, so the nut cannot turn.
ØTTapped hole: smaller than the screw, which cuts its own thread in the plastic. Make it at least screw length + 1 mm deep.

03 · METHODS

Choosing a fastening method

  1. Screw directly into plastic: Simplest, no extra parts. Fine for joints that are rarely taken apart; PLA threads wear out after a few cycles.
  2. Heat-set insert: A brass insert pressed in with heat: reusable threads and good strength, ideal for housings and lids that are opened often. See the Heat-Set Insert Design Guide.
  3. Nut: A hex nut on the back side: the strongest option for high loads. Needs space behind the part or a nut pocket.

04 · DESIGN TIPS

Design tips

Hole orientation

  • Print holes perpendicular to the bed (facing up) for the roundest, most accurate holes.
  • Horizontal holes sag at the top: use a teardrop (pointed) top for small holes, or add 0.2 mm to the diameter.
  • Counterbores and nut pockets facing up need no supports; facing down, leave room to remove supports.

Nut pockets

  • Side-entry pocket: a slot as wide as across flats + 0.3 lets you slide the nut in from the side.
  • Print-in: pause at the top of the pocket, drop the nut in and resume; it is fully enclosed (mention it when you request a quote).
  • Keep at least 1.5 mm of solid wall around the pocket so it does not crack when tightened.

Screw length

  • Through a nut: length ≈ clamped thickness + nut thickness + 2–3 threads.
  • Screwing into plastic: engage at least 2 × the screw diameter (e.g. 6 mm for M3).
  • Flat head screw length includes the head; socket head screw length does not.

Strength & tightening

  • Make the material around holes solid or add a boss; use at least 3–4 walls.
  • Tighten until snug, not more; cracked or stripped plastic cannot be repaired.
  • For joints that are opened often or carry high loads, use heat-set inserts or nuts.

05 · MATERIALS

Materials

GoodPLA / PLA+Fine for clearance holes, counterbores and nut pockets; screwing directly works but strips after repeated assembly.
GoodPETGTough; threads cut directly into PETG last longer than in PLA.
GoodABS / ASA / PCStrong and heat-resistant, good for mechanisms and parts that are assembled often.
GoodResin (SLA)Brittle; screwing directly may crack it. Use clearance holes with nuts, or ask us about inserts.
CautionTPU (flexible)Too soft to hold a screw tight; use a clearance hole with a nut, or keep rigid parts separate.

06 · CHECKLIST

Checklist before sending

Not sure about your design? Send it to us

Share your file or a screenshot and we will check the holes and screw sizes. Screws and nuts can be ordered together with your 3D printing.

Contact us on LINE Download PDF Guide